Did you get Xiaomi Redmi K30 Pro (codename: LMI) smartphone? Then this guide will be useful to you. If you have bricked your device, lost your pattern lock details or are not able to verify your Google account after the hard reset, then you can bypass it quickly using this guide.
You can easily get the ISP PinOUT connection of the Xiaomi Redmi K30 Pro by following the full guide below along with images. By using the ISP PinOUT, you can easily restore the stock ROM, bypass FRP lock or reset user data on your device via UFi Box. In this guide, we will also guide on how to reboot into 9008 EDL Mode.
What is ISP PinOUT?
ISP or In-system programming also known as in-circuit serial programming (ICSP) for hardware that has a cross-reference of pins or contacts. By shorting the pins together, you can power or signal the logic board (motherboard) of an electronic device such as a mobile, computer. You will find the IS Pinout connection on the logic board of your device. Therefore, you will need to remove the back panel of the handset and follow the below image to locate the pinout.
Redmi K30 Pro ISP Pinout Image:
How to Enter EDL Mode on Redmi K30 Pro (LMI)
Follow this instruction carefully to boot your device into EDL Mode (aka Emergency DownLoad Mode)
Method 1: Using ADB
- Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
- Connect your device to your PC
- Open the adb command and enter the command
- .\adb reboot edl
Method 2: Using Fastboot
- Download ADB and Fastboot Tool and extract it in your PC (C:/ Drive)
- Boot your device into bootloader
- Open the command window on your PC on the same folder extracted (ADB and Fastboot Tool)
- now enter the command
- .\fastboot oem edl
Method 3: By Hardware Test Points / Restore Your device
- Download the QDLoader driver
- Find the EDL PinOUT/Test Point on your device (refer image above to find the test point)
- To enter EDL mode, you need to use a metal tweezer or a conductive metal wire to short the points.
- Once you are done, connect your device to PC using USB cable
- This way, your device will enter EDL mode. Now you can open the QFil or QPST Tool to flash the firmware and restore your device.
How to Bypass FRP lock on Redmi K30 Pro using ISP Pinout
Follow this method to bypass the FRP or Google verification using ISP pinout method
What is EDL Mode? How to Enter EDL Mode on Any Qualcomm Device
.\adb reboot edl
.\fastboot oem edl
Required Downloads
- Download UFi Box eMMC Service Tool
- Install Xiaomi USB Drivers on your PC
Pre-Requirements:
- This guide is for Redmi K30 Pro variant only.
- You will need a Windows PC/Laptop and a USB cable.
Instructions
Well, ‘FRP’ known for the term “Factory Reset Protection.” It’s a security measure taken by Google for Android platforms and devices running on the Android 5.1 Lollipop or above version. This functionality gets activated once you sign in to a Google Account on your Android device. And once it is activated, it will prevent you from using the phone until you enter the previous Google Account Credentials. It will remain the same as well, even after doing the factory data reset.
Open the back panel of the device at first.
Connect the wire with the correct ISP Pinout.
Then connect the ISP Pinout to the UFi Box and connect your device via USB cable to the PC.
Go to the Device Manager on your PC.
You will see your device in the list > run the UFi Box and locate the scatter file.
Go to the user Partition / Special Task and click on Reset FRP on the UFI Box.
You’re done.
Steps to Hard Reset Redmi K30 Pro (Bypass Pattern Lock)
Remove the back panel of the Redmi K30 Pro and connect the wire to the ISP Pinout.
Next, connect the correct ISP Pinout to the UFi Box.
Connect your Redmi K30 Pro to the PC via a USB cable.
Head over to the PC and open Device Manager.
If your device is located there, run the UFi Box.
Locate the scatter file > go to the Partition / Special Task on the UFI Box.
Click on Factory Reset.
Enjoy!
That’s it, guys. We hope this guide was helpful to you in order to bypass the FRP Lock or perform a factory reset on your Redmi K30 Pro handset. If you’ve any queries, let us know in the comments below.
Xiaomi Redmi K30 Pro Device Overview
The Redmi K30 Pro 5G features a 6.67 inches Super AMOLED display with a Full HD+ resolution. That said, it has a resolution of 1080 x 2400 pixels, an aspect ratio of 20:9, a screen to body ratio of 87.2 percent, a pixel density of 395 PPI, it can blow up to 500 nits, DCI-P3 100%, HDR 10+. The device pairs with an in-display fingerprint scanner, get protected under the Corning Gorilla Glass 5. Coming to the internals, the Redmi K30 Pro sports the latest Qualcomm Snapdragon 865 SoC. It also pairs with Snapdragon X55 modem and is built on the 7nm process.
This octa-core setup in the SoC includes a single Kryo 585 core, which clocks at a higher speed i.e., at 2.84 GHz, other three Kryo 585 cores which clock at 2.42 GHz. And finally, four Kryo 585 core, which clocks at 1.80 GHz. To the GPU side, it has the Adreno 650, which clocks at 587 MHz. The device runs on the latest MiUi 11 based on the Android 10. Coming to the memory side, it is available in two RAM variants i.e., in the 6GB and 8GB RAM variants. Further, it is available in the 128GB and 256GB Internal storage variants. The 6GB + 128GB variant uses the UFS 3.0 tech. While all other variants come with UFS 3.1 tech. There is no option for expanding the storage via a micro SD card.
Coming to the optics, the Redmi K30 Pro sports a quad rear camera setup arranged in a circular shape. This setup includes a primary 64MP Sony IMX 686 sensor with PDAF. It pairs with a 5MP telephoto macro sensor with support for AF. As a tertiary sensor, it pairs with 13MP ultra-wide sensor, and finally, a 2MP depth sensor. This rear camera setup can shoot videos up to 8K resolution in 24 or 30fps. Just like its predecessor, the Redmi K20 Pro, this also sports a motorized pop-up unit. That said, this unit includes a 20MP sensor with support for HDR photos. It can shoot videos up to 1080 @ 30fps.
The Redmi K30 Pro packs a 4,700 mAh battery, which charges via the USB type c and supports 33W fast charging tech. The brand claims that it can charge up to 100% in 63 minutes. The device supports dual 5G connectivity on-board. Connectivity options on the Redmi K30 Pro include Wi-Fi 802.11 a/b/g, GPS, Bluetooth v5.10, NFC, USB Type-C, 3G, and 4G (with support for Band 40 used by some LTE networks in India) with active 4G on both SIM cards. Sensors on the phone include accelerometer, ambient light sensor, compass/ magnetometer, gyroscope, and proximity sensor. Apart from the in-display fingerprint scanner, it also supports for face unlock. Coming to the dimensions, it measures about 163.30 x 75.40 x 8.90mm (height x width x thickness) and weighs about 218.00 grams. It is available in four color options, namely the Moonlight White, Sky Blue, Star Ring Purple, and Space Gray colors.
